Linux write to serial port

writing to serial port from linux command line

From windows I can communicate with a serial port device using following commands:

Device starts the requested operation.

When I try to accomplish the same operation from a stand alone debian box or from a debian virtualbox instance of the same windows machine, I had no luck so far.

Here’s equivalent linux commands(at least I think so)

Can somebody please direct me to the right direction?

3 Answers 3

If you want to use hex codes, you should add -e option to enable interpretation of backslash escapes by echo (but the result is the same as with echo Ctrl R Ctrl B ). And as wallyk said, you probably want to add -n to prevent the output of a newline:

Also make sure that /dev/ttyS0 is the port you want.

will not be interpreted, and will literally write the string \x12\x02 (and append a newline) to the specified serial port. Instead use

which you can construct on the command line by typing Ctrl V Ctrl R and Ctrl V Ctrl B . Or it is easier to use an editor to type into a script file.

The stty command should work, unless another program is interfering. A common culprit is gpsd which looks for GPS devices being plugged in.

SCREEN:

NOTE: screen is actually not able to send hex, as far as I know. To do that, use echo or printf

I was using the suggestions in this post to write to a serial port, then using the info from another post to read from the port, with mixed results. I found that using screen is an «easier» solution, since it opens a terminal session directly with that port. (I put easier in quotes, because screen has a really weird interface, IMO, and takes some further reading to figure it out.)

You can issue this command to open a screen session, then anything you type will be sent to the port, plus the return values will be printed below it:

(Change the above to fit your needs for speed, parity, stop bits, etc.) I realize screen isn’t the «linux command line» as the post specifically asks for, but I think it’s in the same spirit. Plus, you don’t have to type echo and quotes every time.

ECHO:

Follow praetorian droid’s answer. HOWEVER, this didn’t work for me until I also used the cat command ( cat ) while I was sending the echo command.

PRINTF:

I found that one can also use printf’s ‘%x’ command:

Again, for printf, start cat before sending the command.

Источник

How to send data to a serial port and see any answer?

On Linux, I want to send a command string (i.e. some data) to a serial port (containing control characters), and listen to the response (which also usually might contain control characters).

How can I do this as simplest as possible on Linux? An example is appreciated!

5 Answers 5

All devices on Unix are mapped to a device file, the serial ports would be /dev/ttyS0 /dev/ttyS1 . .

First have a look at the permissions on that file, lets assume you are using /dev/ttyS1 .

You will want read.write access, if this is a shared system then you should consider the security consequences of opening it up for everyone.

A very simple crude method to write to the file, would use the simple echo command.

You can have cat running in one terminal, and echo in a 2nd.

If everything is gibberish, then baud rate, bit settings might need setting before you start sending. stty will do that. !! NOTE stty will use stdin as default file descriptor to affect.

This might be enough for you to script something and log ? Not sure what you are trying to achieve.

For a more interactive, remembers your default settings approach would be to use minicom it is just a program which does everything I’ve mentioned so far. (similar to hyperterminal in Windows, you might be familiar).

An intermediate solution, would use a terminal program like screen which will work on a serial device.

man screen man minicom man stty for more information

Источник

Reading and writing to serial port in C on Linux

I’m trying to send/receive data over an USB Port using FTDI, so I need to handle serial communication using C/C++. I’m working on Linux (Ubuntu).

Basically, I am connected to a device which is listening for incoming commands. I need to send those commands and read device’s response. Both commands and response are ASCII characters.

Everything works fine using GtkTerm but, when I switch to C programming, I encounter problems.

What happens is that read() returns 0 (no bytes read at all) or block until timeout ( VTIME ). I’m assuming this happens because write() does not send anything. In that case, device wouldn’t receive command and I cannot receive response. In fact, turning off the device while my program is blocked on reading actually succeded in getting a response (device sends something while shutting down).

Strange thing is that adding this

right after write() call, I receive:

which is exactly what I expect. Only my program doesn’t work as it should, like my device cannot receive what I’m actually writing on port.

I’ve tried different things and solution, also regarding data types (I’ve tried using std::string, such as cmd = «INIT \r» or const char ) but nothing really worked.

Can someone tell me where I’m wrong?

Thank you in advance.

EDIT: Previously version of this code used

unsigned char cmd[] = «INIT \n»

and also cmd[] = «INIT \r\n» . I changed it because command sintax for my device is reported as

I’ve also tried avoiding the O_NONBLOCK flag on reading, but then I only block until forever. I’ve tried using select() but nothing happens. Just for a try, I’ve created a waiting loop until data is avaliable, but my code never exit the loop. Btw, waiting or usleep() is something I need to avoid. Reported one is only an excerpt of my code. Complete code needs to work in a real-time environment (specifically OROCOS) so I don’t really want sleep-like function.

Источник

Linux Serial Ports Using C/C++

Article by:Geoffrey Hunter

Date Published:	June 24, 2017
Last Modified:	November 24, 2020

Overview

Unluckily, using serial ports in Linux is not the easiest thing in the world. When dealing with the termios.h header, there are many finicky settings buried within multiple bytes worth of bitfields. This page is an attempt to help explain these settings and show you how to configure a serial port in Linux correctly.

Everything Is A File

In typical UNIX style, serial ports are represented by files within the operating system. These files usually pop-up in /dev/ , and begin with the name tty* .

Common names are:

• /dev/ttyACM0 — ACM stands for the ACM modem on the USB bus. Arduino UNOs (and similar) will appear using this name.
• /dev/ttyPS0 — Xilinx Zynq FPGAs running a Yocto-based Linux build will use this name for the default serial port that Getty connects to.
• /dev/ttyS0 — Standard COM ports will have this name. These are less common these days with newer desktops and laptops not having actual COM ports.
• /dev/ttyUSB0 — Most USB-to-serial cables will show up using a file named like this.
• /dev/pts/0 — A pseudo terminal. These can be generated with socat .

A listing of the /dev/ directory in Linux with a connected Arduino. The Arduino serial port is present as /dev/ttyACM0.

To write to a serial port, you write to the file. To read from a serial port, you read from the file. Of course, this allows you to send/receive data, but how do you set the serial port parameters such as baud rate, parity, e.t.c? This is set by a special tty configuration struct .

Basic Setup In C

First we want to include a few things:

Then we want to open the serial port device (which appears as a file under /dev/ ), saving the file descriptor that is returned by open() :

One of the common errors you might see here is errno = 2 , and strerror(errno) returns No such file or directory . Make sure you have the right path to the device and that the device exists!

Another common error you might get here is errno = 13 , which is Permission denied . This usually happens because the current user is not part of the dialout group. Add the current user to the dialout group with:

You must log out and back in before these group changes come into effect.

At this point we could technically read and write to the serial port, but it will likely not work, because the default configuration settings are not designed for serial port use. So now we will set the configuration correctly.

When modifying any configuration value, it is best practice to only modify the bit you are interested in, and leave all other bits of the field untouched. This is why you will see below the use of &= or |= , and never = when setting bits.

Configuration Setup

We need access to the termios struct in order to configure the serial port. We will create a new termios struct, and then write the existing configuration of the serial port to it using tcgetattr() , before modifying the parameters as needed and saving the settings with tcsetattr() .

We can now change tty ’s settings as needed, as shown in the following sections. Before we get onto that, here is the definition of the termios struct if you’re interested (pulled from termbits.h ):

Control Modes (c_cflags)

The c_cflag member of the termios struct contains control parameter fields.

PARENB (Parity)

If this bit is set, generation and detection of the parity bit is enabled. Most serial communications do not use a parity bit, so if you are unsure, clear this bit.

CSTOPB (Num. Stop Bits)

If this bit is set, two stop bits are used. If this is cleared, only one stop bit is used. Most serial communications only use one stop bit.

Number Of Bits Per Byte

The CS fields set how many data bits are transmitted per byte across the serial port. The most common setting here is 8 ( CS8 ). Definitely use this if you are unsure, I have never used a serial port before which didn’t use 8 (but they do exist). You must clear all of the size bits before setting any of them with &=

Flow Control (CRTSCTS)

If the CRTSCTS field is set, hardware RTS/CTS flow control is enabled. The most common setting here is to disable it. Enabling this when it should be disabled can result in your serial port receiving no data, as the sender will buffer it indefinitely, waiting for you to be “ready”.

CREAD and CLOCAL

Setting CLOCAL disables modem-specific signal lines such as carrier detect. It also prevents the controlling process from getting sent a SIGHUP signal when a modem disconnect is detected, which is usually a good thing here. Setting CLOCAL allows us to read data (we definitely want that!).

Local Modes (c_lflag)

Disabling Canonical Mode

UNIX systems provide two basic modes of input, canonical and non-canonical mode. In canonical mode, input is processed when a new line character is received. The receiving application receives that data line-by-line. This is usually undesirable when dealing with a serial port, and so we normally want to disable canonical mode.

Canonical mode is disabled with:

Also, in canonical mode, some characters such as backspace are treated specially, and are used to edit the current line of text (erase). Again, we don’t want this feature if processing raw serial data, as it will cause particular bytes to go missing!

If this bit is set, sent characters will be echoed back. Because we disabled canonical mode, I don’t think these bits actually do anything, but it doesn’t harm to disable them just in case!

Disable Signal Chars

When the ISIG bit is set, INTR , QUIT and SUSP characters are interpreted. We don’t want this with a serial port, so clear this bit:

Input Modes (c_iflag)

The c_iflag member of the termios struct contains low-level settings for input processing. The c_iflag member is an int .

Software Flow Control (IXOFF, IXON, IXANY)

Clearing IXOFF , IXON and IXANY disables software flow control, which we don’t want:

Disabling Special Handling Of Bytes On Receive

Clearing all of the following bits disables any special handling of the bytes as they are received by the serial port, before they are passed to the application. We just want the raw data thanks!

Output Modes (c_oflag)

The c_oflag member of the termios struct contains low-level settings for output processing. When configuring a serial port, we want to disable any special handling of output chars/bytes, so do the following:

Both OXTABS and ONOEOT are not defined in Linux. Linux however does have the XTABS field which seems to be related. When compiling for Linux, I just exclude these two fields and the serial port still works fine.

VMIN and VTIME (c_cc)

VMIN and VTIME are a source of confusion for many programmers when trying to configure a serial port in Linux.

An important point to note is that VTIME means slightly different things depending on what VMIN is. When VMIN is 0, VTIME specifies a time-out from the start of the read() call. But when VMIN is > 0, VTIME specifies the time-out from the start of the first received character.

Let’s explore the different combinations:

VMIN = 0, VTIME = 0: No blocking, return immediately with what is available

VMIN > 0, VTIME = 0: This will make read() always wait for bytes (exactly how many is determined by VMIN ), so read() could block indefinitely.

VMIN = 0, VTIME > 0: This is a blocking read of any number of chars with a maximum timeout (given by VTIME ). read() will block until either any amount of data is available, or the timeout occurs. This happens to be my favourite mode (and the one I use the most).

VMIN > 0, VTIME > 0: Block until either VMIN characters have been received, or VTIME after first character has elapsed. Note that the timeout for VTIME does not begin until the first character is received.

VMIN and VTIME are both defined as the type cc_t , which I have always seen be an alias for unsigned char (1 byte). This puts an upper limit on the number of VMIN characters to be 255 and the maximum timeout of 25.5 seconds (255 deciseconds).

“Returning as soon as any data is received” does not mean you will only get 1 byte at a time. Depending on the OS latency, serial port speed, hardware buffers and many other things you have no direct control over, you may receive any number of bytes.

For example, if we wanted to wait for up to 1s, returning as soon as any data was received, we could use:

Baud Rate

Rather than use bit fields as with all the other settings, the serial port baud rate is set by calling the functions cfsetispeed() and cfsetospeed() , passing in a pointer to your tty struct and a enum :

If you want to remain UNIX compliant, the baud rate must be chosen from one of the following:

Some implementation of Linux provide a helper function cfsetspeed() which sets both the input and output speeds at the same time:

Custom Baud Rates

As you are now fully aware that configuring a Linux serial port is no trivial matter, you’re probably unfazed to learn that setting custom baud rates is just as difficult. There is no portable way of doing this, so be prepared to experiment with the following code examples to find out what works on your target system.

GNU/Linux Method

If you are compiling with the GNU C library, you can forgo the standard enumerations above just specify an integer baud rate directly to cfsetispeed() and cfsetospeed() , e.g.:

termios2 Method

This method relied on using a termios2 struct, which is like a termios struct but with sightly more functionality. I’m unsure on exactly what UNIX systems termios2 is defined on, but if it is, it is usually defined in termbits.h (it was on the Xubuntu 18.04 with GCC system I was doing these tests on):

Which is very similar to plain old termios , except with the addition of the c_ispeed and c_ospeed . We can use these to directly set a custom baud rate! We can pretty much set everything other than the baud rate in exactly the same manner as we could for termios , except for the reading/writing of the terminal attributes to and from the file descriptor — instead of using tcgetattr() and tcsetattr() we have to use ioctl() .

Let’s first update our includes, we have to remove termios.h and add the following:

Please read the comment above about BOTHER . Perhaps on your system this method will work!

Saving termios

After changing these settings, we can save the tty termios struct with tcsetattr() :

Reading And Writing

Now that we have opened and configured the serial port, we can read and write to it!

Writing

Writing to the Linux serial port is done through the write() function. We use the serial_port file descriptor which was returned from the call to open() above.

Reading

Reading is done through the read() function. You have to provide a buffer for Linux to write the data into.

Closing

This is a simple as:

Full Example (Standard Baud Rates)

Issues With Getty

Getty can cause issues with serial communication if it is trying to manage the same tty device that you are attempting to perform serial communications with.

To Stop Getty:

Getty can be hard to stop, as by default if you try and kill the process, a new process will start up immediately.

These instructions apply to older versions of Linux, and/or embedded Linux.

1. Load /etc/inittab in your favourite text editor.
2. Comment out any lines involving getty and your tty device.
3. Save and close the file.
4. Run the command

$ init q to reload the /etc/inittab file.

Kill any running getty processes attached to your tty device. They should now stay dead!

Exclusive Access

It can be prudent to try and prevent other processes from reading/writing to the serial port at the same time you are.

One way to accomplish this is with the flock() system call:

Changing Terminal Settings Are System Wide

Although getting and setting terminal settings are done with a file descriptor, the settings apply to the terminal device itself and will effect all other system applications that are using or going to use the terminal. This also means that terminal setting changes are persistant after the file descriptor is closed, and even after the application that changed the settings is terminated 1 .

Источник