loading windows files

19GAYVER91 #1 Отправлено 09 сен 2015 — 12:37

После установки windows 7 максимум при каждом включении компьютера стал появляться чёрный экран с надписью loading windows files и загрузкой,загрузка идёт минуты 3 ,спросил у знакомых сказали что это предзапускная дефрагментация!

У кого была такая проблема и как её убрать?

За ранее Спасибо!Троллинг не уместен!

P.S Виндовс лицензионный

Прикрепленные файлы

• q4Qbrd.jpg125,39К

kueBckuu_HeagekBaT #2 Отправлено 09 сен 2015 — 12:39

Next #3 Отправлено 09 сен 2015 — 12:46

Виндовс как устанавливал? На чистый раздел? С USB? DVD?

А вообще коли виндовс лицензионный — можно обратиться в ЦПП Мелкомяких

19GAYVER91 #4 Отправлено 09 сен 2015 — 12:46

Next (09 Сен 2015 — 09:46) писал:

Виндовс как устанавливал? На чистый раздел? С USB? DVD?

А вообще коли виндовс лицензионный — можно обратиться в ЦПП Мелкомяких

на чистый раздел с диска

RenamedUser_36482350 #5 Отправлено 09 сен 2015 — 12:46

19GAYVER91 #6 Отправлено 09 сен 2015 — 12:52

EXPERTool (09 Сен 2015 — 09:46) писал:

грузятся файлы временных драйверов которые виндовс устанавливает при установке,обычно их удаляют и ставят дрова с диска либо качают ,я вот думаю а если удалить эти самые родные дрова?

Philidor #7 Отправлено 09 сен 2015 — 12:54

Три танкиста выпили по триста, и п. машине боевой

markus886 #8 Отправлено 09 сен 2015 — 12:54

19GAYVER91 (09 Сен 2015 — 12:52) писал:

грузятся файлы временных драйверов которые виндовс устанавливает при установке,обычно их удаляют и ставят дрова с диска либо качают ,я вот думаю а если удалить эти самые родные дрова?

что за бред? это запуск с показом на экране лога загрузки драйверов (нифига притом не временных)

ps отдайте комп нормальному мастеру.

sergey_32768 #9 Отправлено 09 сен 2015 — 12:55

19GAYVER91 (09 Сен 2015 — 12:37) писал:

После установки windows 7 максимум при каждом включении компьютера стал появляться чёрный экран с надписью loading windows files и загрузкой,загрузка идёт минуты 3 ,спросил у знакомых сказали что это предзапускная дефрагментация!

У кого была такая проблема и как её убрать?

За ранее Спасибо!Троллинг не уместен!

P.S Виндовс лицензионный

Судя по картинке Ваша винда загружается в безопасном режиме после какого то сбоя.

markus886 #10 Отправлено 09 сен 2015 — 12:56

ramzesll (09 Сен 2015 — 12:54) писал:

если бы на винте был бэд-блок — при старте был бы автозапуск chkdsk, а у ТСа другая фигня — загрузка в безопасном режиме

19GAYVER91 #11 Отправлено 09 сен 2015 — 12:57

ramzesll (09 Сен 2015 — 09:54) писал:

проверял Auslogics BoostSpeed все сектора целы всё в норме

19GAYVER91 #12 Отправлено 09 сен 2015 — 12:59

sergey_32768 (09 Сен 2015 — 09:55) писал:

Судя по картинке Ваша винда загружается в безопасном режиме после какого то сбоя.

винда голая и нечего не ставилось какой может быть сбой?

Сообщение отредактировал 19GAYVER91: 09 сен 2015 — 13:00

Windows Is Loading Files

My grandad installed windows 7 on his pc. Then once the installation finished it did its final reboot the pc will start back up and then instead of it doing the windows 7 startup it says Windows Is Loading Files and then changes to Windows Vista startup

1. Insert the Windows 7 DVD
2. Restart your computer
3. When asked if you want to boot from your DVD drive, do so.
4. Choose your language, click Next.
5. Click ‘Repair your computer’
6. Select operating system you want to repair.

If you can still boot into Windows Vista, do so and run the Windows Upgrade Advisor.

it will scan your system and provide a report telling you if your PC can run Windows 7 and if there are any known compatibility issues with your programs or hardware.

Windows 7 Upgrade Advisor:
http://www.microsoft.com/downloads/details.aspx?FamilyID=1b544e90-7659-4bd9-9e51-2497c146af15&displayLang=en

1. Disable any security software before attempting to upgrade or do a clean install.
2. Make sure your computer is updated (devices and applications)
3. Disconnect any external devices before installing.
4. Check your hard disk for any errors:
Click Start
Type: CMD, from the results, right click CMD
Click ‘Run as Administrator’
At the Command Prompt, type: chkdsk /r /f
When you restart your system, your computer will be scanned for errors and attempts will be made to correct them.

If all turns out well, run the upgrade again and see if it completes.

При установке зависает запуск на «Windows is booting files» и далее остановка

Всем доброго времени суток.
При попытке установить Windows 7 (сейчас стоит Начальная, хотел поставить к примеру Домашнюю базовую х64) возникает такая проблема — зависает запуск на Starting Windows: после выбора Windows 64(или 32) bit setup идёт «Windows is loading files» и «Windows is booting files» и далее остановка.
Образ записывал несколько раз на отформатированную флeшку — Rufusом, UltraISO и Windows 7 USB DVD Download Tool, при этом она распознаётся как установочная. В первых двух случаях установка зависает на Starting Windows, при использовании . Tool — установка вообще не начинается после выбора устройства. При этом образ проверенный и у многих работает.
Что я делал:
— Как записывал образ — 3 способа выше. Результата нет.
— Пытался аналогично записать на DVD-диск (UltraISO) и запустить установку с него (изменив Boot настройки, разумеется) — эффект тот же самый.
— USB controller [Enabled]
— В Boot меню первым ставил загрузку с USB/CD(DVD)-ROM, вторым стоит всегда Hard Disk
Могу дополнить, если потребуется.

Кто-то сталкивался с подобным? Заранее спасибо, буду благодарен за любые дельные советы

При установке с флешки останавливается на «start booting from usb device»
Здравствуйте! Я пытаюсь установить windows 7 на нетбуке с операционной системой linux uduntu.

При установке ОС с флешки на экран много раз подряд выводится сообщение «Start booting from usb device. «
Переустанавливал систему много раз, такое вижу впервые: пишет много раз подряд Start booting from.

Зависает при установке Windows 7/8 «Начало установки»
Здравствуйте, не могу установить Windows 7/8 на ноутбук hp модели 6-1252sr. Создал загрузочную.

При установке Windows, на этапе «Регистрация компонентов» установка зависает
При установке винды, на этапе «Регистрация компонентов » не подает вообще признаком установки у.

Windows 7 64 bit «Windows is loading files» reboot loop. This is not a question, but a tutorial of sorts.

I purchased an Asus G73JH laptop at Best Buy two days ago. Let me stress that I was and still am happy with this computer.

• Windows 7 Home 64 bit
• Intel Core i7
• ATI Mobility Radeon 5870 GPU

After uninstalling bloatware, installing Avast 5.0 free edition and updating the virus definitions, I updated my stock device drivers from the Asus site (there are some compatibility issues when updating from the respective hardware provider’s sites) and rebooted. After the reboot I configured Windows to my taste and rebooted to ensure that the settings were saved if the computer should happen to freeze. When Windows started again, I used Windows Update while I began the process of transferring my files from my external hard drive. These files are all clean, and pass deep scans with all search options enabled in Avast 5.0 free and Malwarebytes 1.46 paid version. When the transfer was complete, there were 26 updates waiting to be installed and I chose the option to install before shutting down. When the installation was completed the computer shut down and I hit the power button to turn it back on. I saw a black screen and a status bar that said «windows is loading files» before the standard Windows 7 start screen loaded. After that screen, a very generic background appeared with the busy icon quickly replacing the cursor. It idled for about 10 seconds and rebooted. The loop was infinite. Please note that I did not create backup discs after I got my system where I wanted it. I intended to do so after the updates so that the backup would be complete.

Here is what I found while trying to fix this, in no particular order:

• None of the options given after pressing F8 allowed windows to boot. Safe mode loaded to the safe mode screen in Windows without hanging up on any files and rebooted after idling for a seconds. Disabling the automatic restart after failure only brought the Blue Screen Of Death, notifying me of a memory dump.
• The system repair disc that I made on a different computer after this happened loaded fine, but there were absolutely no errors shown in any of the tests it performed.
• System restore does not fix the problem.
• A Windows XP home with SP3 installation disc will ask to format the partition. This was unacceptable because I needed the data I had moved from my external drive.
• I tried Linux Zorin, Pardus, Ubuntu, and Xubuntu but none of them would allow me to access the Windows file structure. These all loaded off of their respective discs, so I knew it was not a hardware failure or malfunction.
• My recovery partition loaded properly, but again, this was not an option. I just needed to see if it was intact.
• I was able to choose the load drivers option and from there I could access my file structure. I was also able to copy folders to my external hard drive after plugging it in. Note that when doing this it does not give confirmation of the copy and paste. Be patient. Also, it only copies folders and all of their contents. Nothing in the folders will show up using this method and you will not be able to choose specific files.
• Since Windows did not fully load, I was unable to use services.msc.
• Using the repair disc to load a command shell worked, but I was unable to launch the control panel to manually uninstall the updates so I do not know if it would have made a difference. If anyone has a command-line entry within the command shell (not in the RUN command within Windows) that will open Control Panel, please post it here.
• I was able to access the registry through the shell, but I do not know the appropriate values to change so I did not alter it. I’m only saying this in case someone that is familiar with editing the registry has this problem. They might be able to find a fix.
• There are absolutely no forums that have a universal fix to this error.
• I did not think of trying to open Windows Explorer from command until now. Doing this may have allowed my to move files or uninstall. I do not know.
• Microsoft cannot fix this error.
• By using the recovery partition after I dumped my data, I found that it will give the option to make a new partition on the same drive. I did not choose this option because I had what I needed, I did not want a dual installation of windows, and I did not know if the file structure on the first OS would remain intact. I did a full reset and am typing this on the laptop in question. Again, there are no hardware issues. I have updated everything and backed it up, but I am keeping automatic updates off. If you do this, you will want to go to your taskbar and open the Action Center (not the automatic updates window). There is an option to no longer receive notifications about that error. I enabled it.

I finally called Microsoft Technical Support at 800-642-7638 (800-MICROSOFT) to get help. If this happens to you, save yourself some time by asking to be transferred to a Windows 7 specialist. Despite answering the automated system’s questions, I did not get through to the right division when it first rang through. I had to explain the problem twice. When the tech picks up and goes through the formalities, explain the problem. After they confirm what your support question is regarding, tell them what you have tried to fix the issue at hand because it will help speed the process. The tech that I spoke to researched it for a few minutes and his response was that I had already tried everything. My remaining option was to back my files up. If this is happening to you, you might need to cut your losses and reformat or do a full system recovery. The tech taught me how to transfer specific files using the notepad. I will include the entire process for those that are not familiar with it.

1. Boot from a Windows 7 repair disc. If you are not given the option to boot from CD or DVD after inserting the repair disc, restart your computer and press F2 when the first screen comes up. This should take you to your BIOS, but the specific key may be different on your unit. If F2 does not work, refer to your computer handbook or user guide. In the BIOS, locate the portion that allows you to change device boot order. When you find it, move your DVD drive to the top of the list. This is usually done by pressing + or minus, but may be F5 and F6 depending on your BIOS. There should be instructions on the screen. After you have done this, choose to save your configuration and exit. When the computer reboots, you should see a message that tells you to press any key to boot from CD or DVD. Do this.
2. Inside the repair disc there is an option to load a command prompt. Click this.
3. Connect the removable drive you wish to transfer files to.
4. Inside the shell, type the word «notepad» without the quotation marks and press Enter. It should load notepad, but if it does not you can try typing: «C:« and pressing Enter. Again, and in any future examples, do not type the quotes. When the directory changes, type «notepad» and press Enter. If notepad does not load, I don’t know what to offer. If it does, go to the File menu, and click Open. When the box pops up, there will be a drop-down menu that has by Text Files» selected by default. Change this to «All Files» and browse to the folder you need to access. If it is in «My Documents», you will find it by going to C:, then going to Users, then choosing whatever folder has your name or profile under it. It will probably not be the Administrator folder. You should now be able to select the files and folders you want to copy.
5. Go back to the shell without closing the open window and type «notepad» again, hitting Enter afterward. If you are unable to see the command shell, close the «Open» window, move the notepad to the side, and move the shell to a corner of your screen. Then browse back to the folders you need. Once the second Notepad opens, go to Files > Open again, but this time go to the removable drive and open it. You will want to move and re-size the windows until you are able to able to see both sets of your files at once.
6. Left-click the folder you wish to copy over, and drag it to the open window for your removable drive. You will not see confirmation that anything is happening, but you should move your cursor to the folders you are moving files from. It will change to a cursor with a square and a plus-sign (+) below and to the right of the cursor itself. When the cursor changes back to normal, the transfer is done. If you are moving small files, it may be quick enough that you will not get a change in the cursor. If it is normal when hovering over the first window, it is done. Also, you will not be able to switch windows or browse while the transfer is happening. When you are able to affect the windows or folders, your transfer had completed. Once you have transferred a folder or file, right-click on the file/folder and select «Properties». Note the size of the directory or file on the disk. Then do the same in your removable drive to confirm that all of the data has transferred without errors. If the sizes do not match, repeat the process until they done.

I hope this helps. I will be posting it in many forums.