INSPECTION PROCEDURE C-6: Power Window Anti-trap Function does not work Normally.

COMMENTS ON TROUBLE SYMPTOM

PROBABLE CAUSES

DIAGNOSTIC PROCEDURE

STEP 1. Check the power window operating current.

Q. Is the check result normal?

Door window glass adjustment (Refer to ). Then go to Step 2.

Replace the power window motor.

STEP 2. Determine a trouble spot.

Q. Which door does the power window anti-trap function fail on?

Driver’s door : Go to Step 3.

Front passenger’s door : Go to Step 5.

Rear right door : Go to Step 10.

Rear left door : Go to Step 15.

STEP 3. Connector check: E-18 power window main switch connector, E-15 front power window motor (driver’s side) connector

Q. Is the check result normal?

Go to Step 4.

Repair the defective connector.

STEP 4. Check of the wiring harness between the E-18 power window main switch connector terminal Nos. 8, 9, 10, 12 and the E-15 front power window motor (driver’s side) connector terminal Nos. 5, 2, 3, 6

Q. Is the check result normal?

Go to Step 20.

Repair the wiring harness.

STEP 5. Connector check: E-03 front power window motor (passenger’s side) connector

Q. Is the check result normal?

Go to Step 6.

Repair the defective connector.

STEP 6. Resistance measurement at E-03 front power window motor (passenger’s side) connector

(1)Disconnect the connector, and measure at the wiring harness side.

(2)Measure the resistance between the E-03 front power window motor (passenger’s side) connector terminal No. 5 and the body earth. OK: Continuity (less than 2 Ω)

Q. Is the check result normal?

Go to Step 8.

Go to Step 7.

STEP 7. Check of the wiring harness between the E-03 front power window motor (Passenger’s side) connector terminal No. 5 and the body earth

note	Prior to the wiring harness inspection, check the C-113 intermediate connector, and repair if necessary.

• Check the earth line for the power window motor revolution detection sensor for open circuit and short circuit.

Q. Is the check result normal?

Go to Step 20.

Repair the wiring harness.

STEP 8. Connector check: E-05 front power window sub switch connector

Q. Is the check result normal?

Go to Step 9.

Repair the defective connector.

STEP 9. Check of the wiring harness between the E-05 front power window sub switch connector terminal Nos. 8, 2, 3 and the E-03 front power window motor (passenger’ side) connector terminal Nos. 3, 2, 6

Q. Is the check result normal?

Go to Step 20.

Repair the wiring harness.

STEP 10. Connector check: E-11 rear power window motor (RH) connector

Q. Is the check result normal?

Go to Step 11.

Repair the defective connector.

STEP 11. Resistance measurement at E-11 rear power window motor (RH) connector

(1)Disconnect the connector, and measure at the wiring harness side.

(2)Measure the resistance between the E-11 rear power window motor (RH) connector terminal No. 5 and the body earth. OK: Continuity (less than 2 Ω)

Q. Is the check result normal?

Go to Step 13.

Go to Step 12.

STEP 12. Check of the wiring harness between the E-11 rear power window motor (RH) connector terminal No. 5 and the body earth

note	Prior to the wiring harness inspection, check the D-36 intermediate connector, and repair if necessary.

• Check the earth line for the power window motor revolution detection sensor for open circuit and short circuit.

Q. Is the check result normal?

Go to Step 20.

Repair the wiring harness.

STEP 13. Connector check: E-10 rear power window sub switch (RH) connector

Q. Is the check result normal?

Go to Step 14.

Repair the defective connector.

STEP 14. Check of the wiring harness between the E-10 rear power window sub switch (RH) connector terminal Nos. 8, 2, 3 and the E-10 rear power window motor (RH) connector terminal Nos. 2, 3, 6

Q. Is the check result normal?

Go to Step 20.

Repair the wiring harness.

STEP 15. Connector check: E-25 rear power window motor (LH) connector

Q. Is the check result normal?

Go to Step 16.

Repair the defective connector.

STEP 16. Resistance measurement at E-25 rear power window motor (LH) connector

(1)Disconnect the connector, and measure at the wiring harness side.

(2)Measure the resistance between the E-25 rear power window motor (LH) connector terminal No. 5 and the body earth. OK: Continuity (less than 2 Ω)

Q. Is the check result normal?

Go to Step 18.

Go to Step 17.

STEP 17. Check of the wiring harness between the E-25 rear power window motor (LH) connector terminal No. 5 and the body earth

note	Prior to the wiring harness inspection, check the D-23 intermediate connector, and repair if necessary.

• Check the earth line for the power window motor revolution detection sensor for open circuit and short circuit.

Q. Is the check result normal?

Go to Step 20.

Repair the wiring harness.

STEP 18. Connector check: E-24 rear power window sub switch (LH) connector

Q. Is the check result normal?

Go to Step 19.

Repair the defective connector.

STEP 19. Check of the wiring harness between the E-24 rear power window sub switch (LH) connector terminal Nos. 8, 2, 3 and the E-25 rear power window motor (LH) connector terminal Nos. 2, 3, 6

Q. Is the check result normal?

Go to Step 20.

Repair the wiring harness.

STEP 20. Retest the system.

Q. Is the check result normal?

Intermittent malfunction (Refer to GROUP 00 — How to Use Troubleshooting/Inspection Service Points — How to Cope with Intermittent Malfunction ).

Replace the power window motor of the door which the power window anti-trap function does not work on.

INSPECTION PROCEDURE C-6: Power Window Anti-trap Function does not work Normally.

COMMENTS ON TROUBLE SYMPTOM

PROBABLE CAUSES

DIAGNOSIS PROCEDURE

STEP 1. Check the power window operating current.

Q. Is the check result normal?

Adjust the door window glass (Refer to ), and then go to Step 2.

Replace the defective power window motor which operating current are abnormal.

STEP 2. Confirm the power window learning function.

Q. Is the check result normal?

Go to Step 3.

Make the power window switch learn the fully closed position of the windows (Refer to ).

STEP 3. Determine a trouble spot.

Q. Which door does the power window anti-trap function fail on?

Driver’s door : Go to Step 4.

Front passenger’s door : Go to Step 7.

Rear right door : Go to Step 13.

Rear left door : Go to Step 19.

STEP 4. Connector check: F-02 power window main switch connector and F-14 front power window motor (RH) connector

Q. Is the check result normal?

Go to Step 5.

Repair the defective connector.

STEP 5. Check the wiring harness from F-02 power window main switch connector terminal Nos. 8, 9, 10 and 12 to F-14 front power window motor (RH) connector terminal Nos. 6, 2, 4 and 5.

Q. Is the check result normal?

Go to Step 6.

Repair the wiring harness.

STEP 6. Retest the system.

After the power window main switch is replaced, check that the driver’s power window anti-trap function works.

(1)Replace the power window main switch.

(2)Check that the driver’s power window anti-trap function works.

Q. Is the check result normal?

The procedure is complete.

Replace the front power window motor (RH).

STEP 7. Connector check: F-06 front power window motor (LH) connector

Q. Is the check result normal?

Go to Step 8.

Repair the defective connector.

STEP 8. Resistance measurement at the F-06 front power window motor (LH) connector.

(1)Disconnect the connector, and measure at the wiring harness side.

(2)Continuity between F-06 front power window motor (LH) connector terminal No.6 and body earth. OK: Continuity exists (2 Ω or less)

Q. Is the check result normal?

Go to Step 10.

Go to Step 9.

STEP 9. Check the wiring harness F-06 front power window motor (LH) connector terminal No.6 to body earth.

note	Prior to the wiring harness inspection, check intermediate connector D-133 and repair if necessary.

• Check the input and output lines to the revolution detection sensor for open or short circuit.

Q. Is the check result normal?

Go to Step 12.

Repair the wiring harness.

STEP 10. Connector check: F-11 front power window sub switch (LH) connector

Q. Is the check result normal?

Go to Step 11.

Repair the defective connector.

STEP 11. Check the wiring harness from F-11 front power window sub switch (LH) connector terminal Nos. 2, 3 and 8 to F-06 front power window motor (LH) connector terminal Nos. 2, 5 and 4.

Q. Is the check result normal?

Go to Step 12.

Repair the wiring harness.

STEP 12. Retest the system.

After the front power window sub switch (LH) is replaced, check that the front passenger’s anti-trap function can be operated by the front power window sub switch (LH).

(1)Replace the front power window sub switch (LH).

(2)Check that the front passenger’s power window anti-trap function works.

Q. Is the check result normal?

The procedure is complete.

Replace the front power window motor (LH).

INSPECTION PROCEDURE B-6: Power Window Anti-trap Function does not work Normally.

COMMENTS ON TROUBLE SYMPTOM

PROBABLE CAUSES

DIAGNOSIS PROCEDURE

STEP 1. Check the power window operating current.

Q. Is the check result normal?

Adjust the door window glass (Refer to ), and then go to Step 2.

Replace the defective power window motor which operating current are abnormal.

STEP 2. Confirm the power window learning function.

Q. Is the check result normal?

Go to Step 3.

Make the power window switch learn the fully closed position of the windows (Refer to ).

STEP 3. Determine a trouble spot.

Q. Which door does the power window anti-trap function fail on?

Driver’s door : Go to Step 4.

Front passenger’s door : Go to Step 7.

Rear right door : Go to Step 13.

Rear left door : Go to Step 19.

STEP 4. Connector check: F-02 power window main switch connector and F-14 front power window motor (RH) connector

Q. Is the check result normal?

Go to Step 5.

Repair the defective connector.

STEP 5. Check the wiring harness from F-02 power window main switch connector terminal Nos. 8, 9, 10 and 12 to F-14 front power window motor (RH) connector terminal Nos. 6, 2, 4 and 5.

Q. Is the check result normal?

Go to Step 6.

Repair the wiring harness.

STEP 6. Retest the system.

After the power window main switch is replaced, check that the driver’s power window anti-trap function works.

(1)Replace the power window main switch.

(2)Check that the driver’s power window anti-trap function works.

Q. Is the check result normal?

The procedure is complete.

Replace the front power window motor (RH).

STEP 7. Connector check: F-06 front power window motor (LH) connector

Q. Is the check result normal?

Go to Step 8.

Repair the defective connector.

STEP 8. Resistance measurement at the F-06 front power window motor (LH) connector.

(1)Disconnect the connector, and measure at the wiring harness side.

(2)Continuity between F-06 front power window motor (LH) connector terminal No.6 and body earth. OK: Continuity exists (2 Ω or less)

Q. Is the check result normal?

Go to Step 10.

Go to Step 9.

STEP 9. Check the wiring harness F-06 front power window motor (LH) connector terminal No.6 to body earth.

note	Prior to the wiring harness inspection, check intermediate connector D-133 and repair if necessary.

• Check the input and output lines to the revolution detection sensor for open or short circuit.

Q. Is the check result normal?

Go to Step 12.

Repair the wiring harness.

STEP 10. Connector check: F-11 front power window sub switch (LH) connector

Q. Is the check result normal?

Go to Step 11.

Repair the defective connector.

STEP 11. Check the wiring harness from F-11 front power window sub switch (LH) connector terminal Nos. 2, 3 and 8 to F-06 front power window motor (LH) connector terminal Nos. 2, 5 and 4.

Q. Is the check result normal?

Go to Step 12.

Repair the wiring harness.

STEP 12. Retest the system.

After the front power window sub switch (LH) is replaced, check that the front passenger’s anti-trap function can be operated by the front power window sub switch (LH).

(1)Replace the front power window sub switch (LH).

(2)Check that the front passenger’s power window anti-trap function works.

Q. Is the check result normal?

The procedure is complete.

Replace the front power window motor (LH).