Простаивает filter failed alt linux

Заметочки

Дисклеймер

воскресенье, 5 декабря 2010 г.

Решение проблемы с /usr/lib/cups/filter/hpcups failed

Случилось мне переустанавливать ArchLinux на своём десктопе. Всё настроил, но возникла странная проблема: не настраивается CUPS для печати.

Вспоминаю, что при настройке через hp-setup получил строку:

error: Python gobject/dbus may be not installed

Само собой, такое меня не устраивало, принтер-то нужен.
Оказалось всё весьма прозаично. HPLIP требовала бинарник python в /usr/bin/python, а там не было ничего. Даже линка. Вот и возмущался CUPS и HPLIP.

Решаем:
1. создаём линк. поскольку у меня в /usr/bin/ нашёлся бинарник python2.7, то:

в gentoo, например, такое же действие будет выглядеть как /etc/init.d/cupsd restart.

5. заново настраиваем принтер. я люблю это делать в терминале, просто нажимая Enter в диалогах, поэтому добавляю ключик -i, чтобы не было графического интерфейса. это нужно и в случае, если нет qt. смотрится это так:

Ну и вот, всё работает.
Правда, в моём случае, приходилось осуществлять ещё одно действие, во избежание ошибки /usr/lib/cups/backend/hp failed

Вот, собственно, и всё 🙂
Конечно, наверняка есть более грамотный и элегантный способ решения проблемы. Но я же не гуру, и не всё знаю-понимаю, что с чем и как работает. Для меня главное, что сейчас могу печатать, и никаких негативных последствий от моих действий, по крайней мере, пока, нет 🙂

Источник

помогите с принтером

Установил автоматом samsung ml-2525w series PXL на принтер samsung 2510ml. отправляю на печать. принтер не реагирует вообще(иногда после простоя начинает мешать тонер но печать не последует). а в задачах пишет что выполнено все. система Lubuntu 14,04

Перемещено jollheef из general

нет. та же ошибка. видимо надо сделать так чтобы программа сама увидела в локале принтер. а так пишет что локальных принтеров не найдено

Простаивает — Файл «/usr/lib/cups/filter/rastertosamsungspl» имеет небезопасные права доступа (0100777/uid=1000/gid=1000).

сначала етого файла не было. я его еле скопировал. теперь пишет что он не безопасен

Я не думаю что ошибся. 2-1 это номер хаба, :1-0 номер конфигурации. 2 номер порта. Может ты драйвер не тот скачал? Мало ли.

All the other entries refer to genuine USB devices and their interfaces. The devices are named by a scheme like this:

In other words, the name starts with the bus number followed by a ‘-‘. Then comes the sequence of port numbers for each of the intermediate hubs along the path to the device.

For example, «1-1» is a device plugged into bus 1, port 1. It happens to be a hub, and «1-1.3» is the device plugged into port 3 of that hub. That device is another hub, and «1-1.3.1» is the device plugged into its port 1.

(для примера 1-1 это устройство всключеное в шину 1 порт 1. Это похоже хаб. Так что 1-1.3 это устройство в порте 3 этого хаба. Это устройство еще один хаб, и 1-1.3.1 это устройство включенное в его 1 порт.)

Мне все же кажется ты дрова не те скачал. Говорил же выше: часто самые геморойные проблемы вызваны самыми смешными причинами. Не раз убеждался.

Источник

ROSAForum

Forum about ROSA Linux Distros

• Темы без ответов
• Активные темы
• Поиск
• Наша команда

После обновления глючит CUPS

После обновления глючит CUPS

Сообщение Yamah » 10 дек 2013, 22:47

Прилетело обновление. После него любой принтер показывает статус «Простаивает — — Filter failed». В том числе и CUPS-PDF.
Без принтера очень неудобно, особенно, когда от этого зависит завтрешнее задания учащимся жены.

Есть возможность исправить?

Rosa Fresh 2012 x 86_64.

Re: После обновления глючик CUPS

Сообщение akdengi » 10 дек 2013, 22:56

Yamah писал(а): Прилетело обновление. После него любой принтер показывает статус «Простаивает — — Filter failed». В том числе и CUPS-PDF.
Без принтера очень неудобно, особенно, когда от этого зависит завтрешнее задания учащимся жены.

Есть возможность исправить?

Rosa Fresh 2012 x 86_64.

Прилетело когда (последнее 1.7.0-5)? И какие принтеры. Последние обновлениеставит cups-filters и foomatic + для Brother фикс, но не трогает остальное.

Для LO печать в PDF теперь делается установкой галочки во вкладке Печать — Настройки — Печатать в файл. Браузеры автоматом детектят PDF вывод.

Попробуйте удалить и поставить принтер заново. Также проверьте наличие foomatic-filters, foomatic-db и cups-filters.

Если принтер HP, то через hpdoctor поставьте все плагины или через CUPS подключаете драйвер hplip или hpcups.

Re: После обновления глючик CUPS

Сообщение Yamah » 11 дек 2013, 07:02

Проблема всплыла в понедельник вечером, 9.12. Обновлялся тоже в воскресенье, 8.12.
На трех машинах уже проблема всплыла. Дома: Samsung CLX-2160 CUPS-PDF, на работе на одной — Xerox WC-3119 CUPS-PDF, на второй — Epson Stylus Photo P50, CUPS-PDF.

В PDF-ку отказывается печатать GIMP и Gwenview.

Обновления на 22 часа МСК 10.12 поставил, перезагрузился, а лучше не стало.

Re: После обновления глючик CUPS

Сообщение akdengi » 11 дек 2013, 10:17

Проверил — GIMP — Печать — печать в файл (pdf) делает. У вас сами принтеры не печатают или что вы пытаетесь на них сделать? То есть скажите как воспроизвести ошибку.

Или у вас не пашет именно программа cups-pdf, которая в contrib и которая никем не обновлялась и работать возможно с новым cups и не будет и НИКАКОГО отношения к cups не имеет и поддерживается сообществом? Если да, то ее можно ее удалить и печать в файл просто.

P.S. На всякий случай отправил пересобираться cups-pdf, вдруг поможет.

Re: После обновления глючик CUPS

Сообщение akdengi » 11 дек 2013, 10:54

Если дело именно в cups-pdf, попробуйте поставить вот этот пакет:

Re: После обновления глючик CUPS

Сообщение Yamah » 11 дек 2013, 13:49

akdengi писал(а): Проверил — GIMP — Печать — печать в файл (pdf) делает. У вас сами принтеры не печатают или что вы пытаетесь на них сделать? То есть скажите как воспроизвести ошибку.

Или у вас не пашет именно программа cups-pdf, которая в contrib и которая никем не обновлялась и работать возможно с новым cups и не будет и НИКАКОГО отношения к cups не имеет и поддерживается сообществом? Если да, то ее можно ее удалить и печать в файл просто.

P.S. На всякий случай отправил пересобираться cups-pdf, вдруг поможет.

У меня не печатают ВСЕ установленные и устанавливаемые принтеры. В system-config-printer в свойствах принтера в поле «состояние» вначале стоит «простаивает». Но стоит только отправить на любой принтер любое задание для печати (хоть из LO, хоть из GIMP, хоть просто тестовую), как в поле состояния любого принтера уже стоит «Простаивает — — Filter failed».

Скриншот дам вечером, когда доберусь до своей обновленной системы.

Как повторить ошибку — ХЗ. Глюк всплыл на тех машинах, которые обновлялись на прошлой неделе.

Источник

Вопрос про CUPS и фильтры печати

Здравствуйте, вопрос теоретический:
Имеется cups и принтер Kyocera FS-1060DN. Под Linux есть «драйвер» — ppd и бинарник rastertokpsl. Поставил, всё вроде хорошо, НО!
Тестовая страница cups и «hello» в leafpad (geany, etc.) печатается на ура, а вот страничка в firefox, pdf из zathura’ы не печатает — «filter failed». И правда, rastertokpsl валится с ошибкой сегментирования.
Я понимаю, драйвер УГ и надо пинать разработчиков, но этот же pdf прекрасно печатается нативным Foxit Reader’ом.
Почему так? Есть различные способы подать в cups страницу? Одна программа шлёт растр, другая вектор? От чего сие зависит? Где узнать подробности?

Неверно обрабатываются параметры в «фильтре»

Благодарю, пошёл проверять.

Тот же принтер, работает по сети.

В хроме выбираю печать — job отваливается с «filter failed». Достаю файл из /var/spool/cups/, открываю его document viewer (evince) — печатается без проблем. Только в первом случает размер джоба 119k, а во втором 92k

Нет, осталась бага. «Решаю» подобным вам способом: печатаю в файл (в pdf), потом печатаю оный. Успех в 100%. А оригинал (в том числе и pdf-ки) процентах в 90 сбоят.
Наскрипеть, чтобы перед печатью cups сам проделывал такое руки не доходят — скажите, если сдюжите.

Источник

CUPS/Troubleshooting

This article covers all non-specific (ie, not related to any one printer) troubleshooting of CUPS and printing drivers (but not problems related to printer sharing), including methods of determining the exact nature of the problem, and of solving the identified problem.

Contents

Debug log

The best way to get printing working is to set ‘LogLevel’ in /etc/cups/cupsd.conf to:

And then viewing the output from /var/log/cups/error_log like this:

The characters at the left of the output stand for:

These files may also prove useful:

• /var/log/cups/page_log — Echoes a new entry each time a print is successful
• /var/log/cups/access_log — Lists all cupsd http1.1 server activity

Print a document and watch error_log to get a more detailed and correct image of the printing process.

Problems resulting from upgrades

Issues that appeared after CUPS and related program packages underwent a version increment

CUPS stops working

The chances are that a new configuration file is needed for the new version to work properly. Messages such as «404 — page not found» may result from trying to manage CUPS via localhost:631, for example.

To use the new configuration, copy /etc/cups/cupsd.conf.default to /etc/cups/cupsd.conf (backup the old configuration if needed) and restart CUPS to employ the new settings.

All jobs are «stopped»

The factual accuracy of this article or section is disputed.

If all jobs sent to the printer become «stopped», delete the printer and add it again. Using the CUPS web interface, go to Printers > Delete Printer.

To check the printer’s settings go to Printers, then Modify Printer. Copy down the information displayed, click ‘Modify Printer’ to proceed to the next page(s), and so on.

All jobs are «The printer is not responding»

On networked printers, you should check that the hostname in the printer’s URI resolves to the printer’s IP address via DNS, e.g. if your printer’s connection looks like this:

then the hostname ‘BRN_020554’ needs to resolve to the printer’s IP from the server running CUPS. If Avahi is being used, ensure that Avahi’s hostname resolution is working.

Alternatively, replace the hostname used in the URI with the printer’s IP address.

The PPD version is not compatible with gutenprint

And restart CUPS (as pointed out in gutenprint’s post-install message).

_2.3.3+106+ga72b0140e-1″>Issues Relating to Upgrade 2.3.3-3 -> 2.3.3+106+ga72b0140e-1

As a side-effect of switching Arch’s CUPS upstream from Apple’s senescent original to the actively-developed OpenPrinting fork in November 2020, the names of the CUPS systemd services were changed. The changes map as follows:

• org.cups.cups-lpd.socket→cups-lpd.socket
• org.cups.cups-lpd@.service→cups-lpd@.service
• org.cups.cupsd.socket→cups.socket
• org.cups.cupsd.service→cups.service
• org.cups.cupsd.path→cups.path

The CUPS install file for that upgrade recommends:

So, if one had org.cups.cupsd.service enabled, one would disable it with immediate effect ( #systemctl —now disable org.cups.cupsd.service ) and enable its successor, also with immediate effect ( #systemctl —now enable cups.service ).

In addition to disabling the services under their own name and re-enabling them under the new, if you have made any non-standard modifications such as dropin files (e.g., /etc/systemd/system/org.cups.cupsd.service.d ) or adding the services as «Wants=» to target or other custom services, those will need to be moved over as well.

Networking issues

Unable to locate printer

Even if CUPS can detect networked printers, you may still end up with an «Unable to locate printer» error when trying to print something. The solution to this problem is to enable Avahi’s .local hostname resolution. See CUPS#Network for details.

This problem may also arise when you have a firewall. You may need to disable your firewall or set the right rules. Using system-config-printer to detect network printers will do that automatically.

Similarly, being connected to a VPN may also cause CUPS to be unable to locate the printer. Disabling any VPN connections temporarily for printing can help fixing it.

Old CUPS server

As of CUPS version 1.6, the client defaults to IPP 2.0. If the server uses CUPS version=1.1 option documented at [1] to the URI.

Unable to locate PPD file

Make sure Avahi is set up correctly. In particular, make sure nss-mdns is installed and set up in /etc/nsswitch.conf .

Finding URIs for Windows print servers

Sometimes Windows is a little less than forthcoming about exact device URIs (device locations). If having trouble specifying the correct device location in CUPS, run the following command to list all shares available to a certain windows username:

This will list every share available to a certain Windows username on the local area network subnet, as long as Samba is set up and running properly. It should return something like this:

What is needed here is first part of the last line, the resource matching the printer description. So to print to the EPSON Stylus printer, one would enter:

as the URI into CUPS.

USB printers

Conflict with SANE

If you are also running SANE, it’s possible that it is conflicting with CUPS. To fix this create a Udev rule marking the device as matched by libsane:

Conflict with usblp

USB printers can be accessed using two methods: The usblp kernel module and libusb. The former is the classic way. It is simple: data is sent to the printer by writing it to a device file as a simple serial data stream. Reading the same device file allows bi-di access, at least for things like reading out ink levels, status, or printer capability information (PJL). It works very well for simple printers, but for multi-function devices (printer/scanner) it is not suitable and manufacturers like HP supply their own backends. Source: here.

If you have problems getting your USB printer to work, you can try blacklisting the usblp kernel module:

Custom kernel users may need to manually load the usbcore kernel module before proceeding.

Once the modules are installed, run:

Then plug in the printer and inspect the output to see if it was detected.

If you are using usblp , the output should indicate that the printer has been detected like so:

If you blacklisted usblp , you will see something like:

USB autosuspend

The Linux kernel automatically suspends USB devices when there is driver support and the devices are not in use. This can save power, but some USB printers think that they are disconnected when the kernel suspends the USB port, preventing printing. This can be fixed by deactivating autosuspend for the specific device, see Power management#USB autosuspend.

Bad permissions

Check the permissions of the printer USB device. Get the bus and device number from lsusb :

Check the ownership by looking in devfs:

The cups daemon runs as user «cups» and belongs to group «lp», so either this user or group needs read & write access to the USB device. If you think the permissions look wrong, you can change the group and permission temporarily:

Then check if cups can now see the USB device correctly.

To make a persistent permission change that will be triggered automatically each time the USB device is attached, add the following line:

After editing, reload the udev rules with this command:

Each system may vary, so consult udev#List the attributes of a device wiki page.

HP issues

CUPS: «/usr/lib/cups/backend/hp failed»

Try adding the printer as a Network Printer using the http:// protocol.

CUPS: Job is shown as complete but the printer does nothing

This happens on HP printers when you select the (old) hpijs driver (e.g. the Deskjet D1600 series). Use the hpcups driver instead.

Some HP printers require their firmware to be downloaded from the computer every time the printer is switched on. If there is an issue with udev (or equivalent) and the firmware download rule is never fired, you may experience this issue. As a workaround, you can manually download the firmware to the printer. Ensure the printer is plugged in and switched on, then run

CUPS: ‘»foomatic-rip» not available/stopped with status 3’

If receiving any of the following error messages in /var/log/cups/error_log while using a HP printer, with jobs appearing to be processed while they all end up not being completed with their status set to ‘stopped’:

make sure hplip has been installed.

CUPS: «Filter failed»

A «filter failed» error can be caused by any number of issues. The CUPS error log (by default /var/log/cups/error_log ) should record which filter failed and why.

Missing ghostscript

Install ghostscript ( /usr/lib/cups/filter/gstoraster needs it to run).

Missing foomatic-db

Install foomatic-db and foomatic-db-ppds . This fixes it in some cases.

Avahi not enabled

Start, and enable the avahi-daemon service.

Out-of-date plugin

This error can also indicate that the plugin is out of date (version is mismatched) and may occur after a system upgrade, possibly showing up as a Plugin error message in the logs. If you have installed hplip-plugin AUR you will need to update the package, otherwise re-run hp-setup -i to install the latest version of the plugin.

Outdated printer configuration

As of hplip-plugin AUR v3.17.11 hpijs is not longer available. If you have printers using hpijs they will fail to print. You must modify them and select the new hpcups driver instead.

You can check if this is your case looking at cups error_log:

Client and host both run CUPS with hpcups

A bug seems to affect CUPS when a host shares a physically connected HP printer using hpcups drivers from hplip , and a client adds the shared printer in is own CUPS server through IPP, using hpcups driver too. On every attempt to print a page from the client, the jobs page from the client returns indefinitly «Sending data to printer» while the same page from the host returns «Filter failed». It appears that the job runs through the CUPS filter twice: a first time on client-side, and a second time on host-side, which makes it fails on host-side. The same bug should not be observed when printing from a Windows client, or when printing directly on the host. There are some workarounds here (use only one method):

• Use Generic IPP Everywhere Printer driver on the client. When selecting the driver in the CUPS Web Interface, you should find it in the Generic manufacturer.
• Modify the PPD used on the client side so the job does not goes through the filter client-side. Find the right PPD in /usr/share/ppd/HP and copy it in your home directory. Edit the copy : replace the line *cupsFilter: «application/vnd.cups-raster 0 hpcups» with *cupsFilter: «*/* 0 -» . Now, add your printer on the client CUPS, selecting your custom PPD located in your home directory.
• Create a raw queue on the host: when you add the printer in the CUPS interface of the host, do not select the specific PPD of your printer, but choose Raw queue from Raw manufacturer. You should be able to add this shared printer on the client, using this time the specific PPD of the printer. With this method, the host is not able to print directly a document because it does not run the filter. However, if the host is a small headless embedded device such as a Raspberry Pi, you might notice an important decrease of the response time with this method compared to the two previous ones, especially with large documents, because it saves a lot a CPU usage.

CUPS: prints only an empty and an error-message page on HP LaserJet

This article or section is out of date.

There is a bug that causes CUPS to fail when printing images on HP LaserJet (in my case 3380). The bug has been reported and fixed by Ubuntu. The first page is empty, the second page contains the following error message:

In order to fix the issue, run the following command as root:

CUPS: «File «/usr/lib/cups/filter/rastertospl» not available

After the printer is connected by other means to the network, setting up the HP 107w Laser printer is possible through the CUPS web interface; but this error prevents printing.

It seems that support for this printer is not provided by hplip. However, drivers can be installed using HP’s install scripts and PPD file found at the HP downloads page.

Extract the .zip and read this gist for further details and instructions.

HPLIP 3.13: Plugin is installed, but HP Device Manager complains it is not

The issue might have to do with the file permission change that had been made to /var/lib/hp/hplip.state . To correct the issue, a simple chmod 644 /var/lib/hp/hplip.state and chmod 755 /var/lib/hp should be sufficient. For further information, please read this link.

hp-toolbox: «Unable to communicate with device»

Virtual CDROM printers

This can also be caused by printers such as the P1102 that provide a virtual CD-ROM drive for MS Windows drivers. The lp dev appears and then disappears. In that case, try the usb-modeswitch and usb-modeswitch-data packages, that lets one switch off the «Smart Drive» (udev rules included in said packages).

Networked printers

This can also occur with network attached printers using dynamic hostnames if the avahi-daemon is not running. Another possibility is that hp-setup failed to locate the printer because the IP address of the the printer changed due to DHCP. If this is the case, consider adding a DHCP reservation for the printer in the DHCP server’s configuration.

hp-setup asks to specify the PPD file for the discovered printer

Furthermore, when selecting a PPD file in hp-setup’s graphical mode, the field does not update and no error message is shown.

Or, if in interactive (console) mode, you may encounter something similar to this even when providing a correct path to a valid ppd file:

The solution is to install and start cups before running hp-setup .

hp-setup: «Qt/PyQt 4 initialization failed»

Install python-pyqt4 AUR , which is an optdepend of hplip . Alternatively, to run hp-setup with the command line interface, use the -i flag.

hp-setup: finds the printer automatically but reports «Unable to communicate with device» when printing test page immediately afterwards

This at least happens to hplip 3.13.5-2 for HP Officejet 6500A through local network connection. To solve the problem, specify the IP address of the HP printer for hp-setup to locate the printer.

hp-setup: «KeyError: ‘family-class'»

If adding a printer fails silently in the UI or you receive a KeyError: ‘family-class’ traceback from hp-setup , the /usr/share/hplip/data/models/models.dat may need to be manually updated. Check if family-class=Undefined is defined the section for your printer, if not add it:

Other

Printer «Paused» or «Stopped» with Status «Rendering completed»

Low ink

When low on ink, some printers will get stuck in «Rendering completed» status and, if it is a network printer, the printer may even become unreachable from CUPS’ perspective despite being properly connected to the network. Replacing the low/depleted ink cartridge(s) in this setting will return the printer to «Ready» status and, if it is a network printer, will make the printer available to CUPS again.

Printing fails with unauthorised error

If a remote printer requests authentication CUPS will automatically add an AuthInfoRequired directive to the printer in /etc/cups/printers.conf . However, some graphical applications (for instance, some versions of LibreOffice [2]) have no way to prompt for credentials, so printing fails. To fix this include the required username and password in the URI. See [3], [4].

Unknown supported format: application/postscript

Comment the lines:

from /etc/cups/mime.convs , and:

Print-Job client-error-document-format-not-supported

Try installing the foomatic packages and use a foomatic driver.

Unable to get list of printer drivers

(Also applicable to error «-1 not supported!»)

Try to remove Foomatic drivers or refer to CUPS/Printer-specific problems#HPLIP for a workaround.

lp: Error — Scheduler Not Responding

If you get this error, ensure CUPS is running, the environmental variable CUPS_SERVER is unset, and that /etc/cups/client.conf is correct.

«Using invalid Host» error message

Try adding ServerAlias * into /etc/cups/cupsd.conf .

Cannot print from LibreOffice

If you can print a test page from the CUPS web interface, but not from LibreOffice, try to install the a2ps package.

Printer output shifted

This seems to be caused by the wrong page size being set in CUPS.

Printer becomes stuck after a problem

When an issue arises during printing, the printer in CUPS may become unresponsive. lpq reports that the printer is not ready , and it can be reactivated using cupsenable . In the CUPS web interface, the printer is shown as Paused, and can be reactivated by resuming the printer.

To automatically have CUPS reactivate the printer, change ErrorPolicy from the default stop-printer to retry-current-job .

Samsung: URF ERROR — Incomplete Session by time out

This error is usually encountered when printing files over the network through IPP to a Samsung printer, and is solved by using the samsung-unified-driver AUR package.

Brother: Printer prints multiple copies

Sometimes the printer will print multiple copies of a document (for instance a MFC-9330CDW printed 10 copies). The solution is to update the printer firmware.

Regular user cannot change properties of the printer or remove certain jobs

If a regular user needs to be able to change the printers properties or manage the printer queue, the user may need to be added to the sys group.

Cannot login into web interface

Check if there is more than one cupsd process running. If this is the case then stop cups service, kill all processes named cupsd and start cups service again.

Источник